Free US shipping on orders over $144.98 to the lower 48 states*.

Home Attic Vent Calculator

Solar Blaster · Home Attic Vent Calculator

Your code-required roof vents, with a solar boost built in.

Same hole. No new cuts.One exhaust typeWorks 24/7, boosts in the sun

Find your attic's code-required vent area in about a minute. Then see how many Solar Blaster hybrid vents fit in the openings your roof already has. When the sun's out, the fan boosts airflow. The rest of the time it vents passively, like any roof vent.

1 Your attic

×

2 Your roof and vents today

3 Your local code

4 Intake (eaves / soffits) optional

Advanced: vent ratings and fan model

? How attic airflow works

Cool air in low (eaves) Hot air out high

Think of a hot air balloon. It breathes in at the bottom and rises because warm air is lighter. Your attic works the same way. Cool air comes in low at the eaves, and hot, damp air leaves high near the ridge, the same way a house with eave and ridge vents is built to breathe. That steady flow gives you "clothesline fresh" air in the attic and helps reduce moisture and mold risk.

Gable vents are different. Gable vents (the wall vents at each end of the attic) are wind-driven. Wind blows in one end and out the other, so they work best when the wind is blowing across the house and much less on still days. Solar Blaster vents use natural convection instead: cool air in low, hot air out high, with a solar boost when the sun is out.

Why a Solar Blaster vent instead of an add-on solar fan? A Solar Blaster vent is the roof vent: a standard-style passive exhaust vent with a small solar fan built in. When the sun is out, the fan boosts the natural flow. At night and on still days, it keeps venting passively like any other roof vent. A stand-alone solar attic fan is an extra unit added on top of the vents you already have.

Why "bigger" isn't better. An add-on fan rated at 1,000+ CFM has to pull its air from somewhere. If the easiest path is the vent next to it rather than the eaves, the other exhaust vents can turn into intakes. Air then short-circuits across the top of the attic, and the lower attic gets little airflow. Vent makers call this mixing exhaust types and tell installers not to do it. GAF also warns that a power fan mixed with soffit and ridge vents "could result in reverse air flow" and leaks. When intake is short, a strong fan can also pull cooled air up out of the house through ceiling gaps. It can also pull in outside air through whatever opening is nearest, so if a chimney or smoker is close to one of those vents, some of that smoke can come in with the air.

Solar Blaster takes the opposite approach: several low-CFM vents (35.2 or 96 CFM each), spread evenly along the top of the roof, all the same type. That's in line with the U.S. Department of Energy's Building America guidance. If a fan is used, it says to use a lower-CFM, solar-powered unit, with ample intake low and the fan high. Its target is about 50 CFM per 1,000 sq ft of attic floor.

§ Sources and fine print

  • Vent area: International Residential Code R806.2 (2021 and 2024 text): minimum 1/150 of the vented area; 1/300 allowed when 40 to 50% of the area is in upper vents within 3 ft of the ridge, the rest is in the bottom third, and (zones 6 to 8 only) a Class I or II ceiling vapor retarder is installed. The 2018 IRC allowed 1/300 when either condition was met. UpCodes R806.2
  • Local: Fountain Hills adopted the 2024 IRC for permits received on or after Sept 1, 2025 (Town of Fountain Hills), with no amendment to R806 (Town Code 7-1-2). Phoenix adopted the 2024 IRC effective Aug 1, 2025 (City of Phoenix). Maricopa County moves from the 2018 to the 2024 codes for plans submitted on or after Nov 20, 2026 (Maricopa County).
  • Split and balance: Air Vent, Lomanco, GAF and Owens Corning all split required area 50/50 between intake and exhaust, and say exhaust should never exceed intake.
  • Fans: DOE Building America Solution Center, Attic Ventilation Fans; ENERGY STAR, About Attic Ventilation; Air Vent / ARMA, "Do Not Mix Attic Exhaust Vents"; GAF Technical Bulletin R-120.
  • Fan ratings are free-air specs. Real airflow depends on intake, vent restriction and wind. Air-exchange times assume proper intake ventilation.
  • Check your local code. This calculator gives an estimate for planning. Your building official, your roof and vent makers' instructions, and your shingle warranty have the final say. Shingle makers including GAF, Owens Corning, CertainTeed, IKO, Atlas, TAMKO and Malarkey limit or exclude warranty coverage for inadequate ventilation.