For about 15 years, Solar Blaster has been making a simple case: multiple small fans ventilate a roof more uniformly, and in a more balanced way, than one large fan. Owner Dan Rheaume has been on roofs for about 45 years, and he saw the problem long before the market wanted to talk about it. One big fan pulls hard from a single point. It leaves dead zones. It can rob air from the vents that building codes and shingle warranties already require, and even turn those exhaust vents into intakes.
Those vents are not an optional extra. They are already mandated by building code, and shingle manufacturers' warranties depend on them. Unlike add-on solar fans, Solar Blaster vents are those code-required, warranty-required vents themselves.
The rest of industry has been catching up: fan banks on barns and greenhouses, fan walls in air handlers and data centers, distributed cooling in electric-vehicle battery packs, and new electric aircraft that use many battery-powered fans instead of two large engines. The principle is the same one Solar Blaster has been building into solar roof vents from Fountain Hills, Arizona: spread the work, keep the pressure even, and don't bet everything on a single blower.
A roofer's idea, 15 years ahead
Dan didn't come at this as a marketing slogan. He came at it as a roofer. After decades on attics, sheds, and later shipping containers, the pattern was obvious: a single high-volume add-on solar attic fan can short-circuit, drawing from the nearest opening instead of washing the whole roof deck.
The International Residential Code already requires roof ventilation for enclosed attics. Section R806, Roof Ventilation, sets a minimum net free ventilating area of 1/150 of the vented space. That minimum may be 1/300 when the code's conditions are met, including putting 40 to 50 percent of the vent area in the upper portion of the attic — not more than 3 feet below the ridge — and the balance in the bottom third. Arizona does not impose one statewide residential code for houses; cities and counties adopt the IRC. Fountain Hills, where Solar Blaster is based, has adopted the 2024 IRC.
Shingle manufacturers write the same expectation into their warranties. GAF's Shingle & Accessory Limited Warranty does not cover damage from "inadequate ventilation," and GAF's warranty guide tells homeowners that conditions other than a manufacturing defect — including "failure to install adequate ventilation" — are not covered. Owens Corning's standard limited warranty does not cover "damage caused by improper or inadequate roof ventilation," and Owens Corning recommends a balanced intake-and-exhaust system that meets or exceeds code. CertainTeed's 2025 limited warranty reduces coverage to 10 years and withholds SureStart protection when shingles are applied to an inadequately ventilated or non-ventilated deck.
Unlike add-on solar fans, a Solar Blaster vent is that already-required exhaust. It sits where a passive exhaust vent belongs, boosts that opening when the sun is out, and still vents passively when it isn't. Several modest solar vents along the ridge work inside the code's high-and-low design. One oversized add-on fan can work against it.
Solar Blaster has been saying so for about 15 years, well ahead of a market that was busy selling bigger CFM. The world has since filled up with examples that make the same point.
Industry already voted for many small fans
Electric planes and drones. In November 2026, a new Chinese electric commuter aircraft — COMAC's CE-25A — completed its first crewed flight with ten battery-powered ducted fans along the wings, five per side, instead of two large engines. Multi-rotor drones work the same way: many small motors share the lift, so losing one unit is not a disaster. Several Solar Blaster vents along the ridge share the exhaust so the whole deck is pulled evenly.
Data centers and computers. Server rooms and data-center cooling units increasingly use arrays of fans, and the computer on your desk is already cooled by several small fans, so every chip stays in range. One large fan leaves hot spots. An attic, a shed, or a 40-foot container has corners too. Distributed vents keep air moving in all of them.
HVAC fan walls. Commercial air handlers have been replacing a single large blower with a fan wall: a grid of smaller fans that pushes air more evenly and stays online if one motor goes down. That redundancy is the Solar Blaster layout in a nutshell.
Greenhouses, poultry houses, and dairy barns. These buildings have used banks of fans for years so no bay goes stale. A line of solar vents along a long ridge, a shed row, or a shipping container does the same job.
Mines and tunnels. Underground ventilation often places booster fans at intervals rather than asking one giant fan at the portal to do all the work. Air in an attic or a container has to travel a distance too. Multiple exhaust points keep that path shorter and the flow more even.
EV battery packs. Electric-vehicle batteries are cooled across the pack — multiple fans, channels, or both — because a single cooling point cannot keep every cell in range. Heat and moisture in a roof space collect in pockets the same way. Several vents at the high point pull from the whole space, not just one pocket.
What that means on a roof
Several modest fans spread along the high point keep pressure more even across the roof deck, so airflow does not pile up at one penetration. That means fewer dead zones. If one fan is shaded, dirty, or down, the others keep working. A single large fan has no backup.
And unlike add-on solar fans, each Solar Blaster vent is the code-required, warranty-required exhaust itself. A single add-on solar attic fan can rob air from the vents that code and shingle warranties already require, and turn those exhaust vents into intakes. Solar Blaster does not sit on top of the ventilation system. It is the system: a hybrid solar vent that boosts exhaust when the sun is strongest and still acts as a passive vent when it is not.
The layout stays simple. Intake low, exhaust high — the same high-and-low split the code describes. Do not treat a gable vent as a substitute for that path. Gable vents are wind-driven, not convective. They help when the wind cooperates, but they are not the same as low soffit or eave intake and high ridge exhaust.
For a built-in example, look at the Solar RidgeBlaster. It puts three 35.2 CFM fans in one ridge unit, about 105.6 CFM total, so the exhaust is already spread instead of dumped through a single hole. On longer roofs, sheds, and containers, use several vents so the same idea scales down the run. See also Why Solar Blaster Bets on Balance, Not Brute Force.
The result is not a health claim and it is not a miracle. Moving air through the whole space helps reduce moisture and mold risk, and leaves you with clothesline fresh air.
Ahead of its time, and still the right call
Dan has been making this argument for about 15 years. The plane, the data center, the barn, and the fan wall caught up to a point a roofer in Fountain Hills was already building into a product. Multiple small fans beat one big fan. That is how you ventilate a roof uniformly, and in a balanced way — with the vents that code and shingle warranties already require.
Powered by the Sun.
Questions about your attic, shed, or container? Visit solarblasterfans.com or call 480-747-7097.